U.S. PHARMACOPEIA

Search USP29  
Betamethasone
Click to View Image
C22 H29FO5 392.46

Pregna-1,4-diene-3,20-dione, 9-fluoro-11,17,21-trihydroxy-16-methyl-, (11,16)-.
9-Fluoro-11,17,21-trihydroxy-16-methylpregna-1,4-diene-3,20-dione [378-44-9].
» Betamethasone contains not less than 97.0 percent and not more than 103.0 percent of C22H29FO5, calculated on the dried basis.
Packaging and storage— Preserve in tight containers. Store between 2 and 30.
Identification—
B: Thin-Layer Chromatographic Identification Test 201
Test solution— Prepare a solution of Betamethasone in dehydrated alcohol containing 0.5 mg per mL.
Developing solvent system: a mixture of chloroform and diethylamine (2:1).
Procedure— Proceed as directed in the chapter, except to locate the spots by lightly spraying with dilute sulfuric acid (1 in 2) and heating on a hot plate or under a lamp until spots appear.
Specific rotation 781S: between +118 and +126, calculated on the dried basis.
Test solution: 5 mg per mL, in methanol.
Loss on drying 731 Dry it at 105 for 3 hours: it loses not more than 1.0% of its weight.
Residue on ignition 281: not more than 0.2%, a platinum crucible being used.
Ordinary impurities 466
Test solution: methanol.
Standard solution: methanol.
Application volume: 10 µL.
Eluant: a mixture of toluene, acetone, methyl ethyl ketone, and formic acid (55:20:20:5), in a nonequilibrated chamber.
Visualization: 5.
Organic volatile impurities, Method V 467: meets the requirements, except that the limit for methylene chloride is 0.1%.
Solvent— Use dimethyl sulfoxide.
Residual solvents 467: meets the requirements.
(Official January 1, 2007)
Assay—
Mobile phase— Prepare a filtered and degassed mixture of water and acetonitrile (63:37). Make adjustments if necessary (see System Suitability under Chromatography 621).
Internal standard solution— Prepare a solution of propylparaben in alcohol having a known concentration of about 0.25 mg per mL.
Standard preparation— Dissolve an accurately weighed quantity of USP Betamethasone RS in alcohol to obtain a solution having a known concentration of about 0.2 mg per mL. Transfer 10.0 mL of this solution to a suitable vial, and add 10.0 mL of Internal standard solution, to obtain a Standard preparation having known concentrations of about 0.1 mg of betamethasone and about 0.125 mg of propylparaben per mL.
Assay preparation— Using about 80 mg of Betamethasone, accurately weighed, prepare as directed for Standard preparation.
Chromatographic system (see Chromatography 621)— The liquid chromatograph is equipped with a 240-nm detector and a 4.6-mm × 25-cm column that contains packing L1. The flow rate is about 1.0 mL per minute. Chromatograph the Standard preparation, and record the peak responses as directed for Procedure: the relative retention times are about 1.0 for betamethasone and 1.4 for propylparaben; the resolution, R, between betamethasone and propylparaben is not less than 3.0; and the relative standard deviation for replicate injections is not more than 2.0%.
Procedure— Separately inject equal volumes (about 10 µL) of the Standard preparation and the Assay preparation into the chromatograph, record the chromatograms, and measure the responses for the major peaks. Calculate the quantity, in mg, of C22H29FO5 in the portion of Betamethasone taken by the formula:
800C(RU / RS),
in which C is the concentration, in mg per mL, of USP Betamethasone RS in the Standard preparation; and R U and R S are the peak height ratios of the betamethasone peak and the internal standard peak obtained from the Assay preparation and the Standard preparation, respectively.
Auxiliary Information— Staff Liaison : Daniel K. Bempong, Ph.D., Scientist
Expert Committee : (MDPS05) Monograph Development-Pulmonary and Steroids
USP29–NF24 Page 264
Pharmacopeial Forum : Volume No. 29(5) Page 1427
Phone Number : 1-301-816-8143