U.S. PHARMACOPEIA

Search USP29  
Cephapirin for Injection
» Cephapirin for Injection contains an amount of Cephapirin Sodium equivalent to not less than 90.0 percent and not more than 115.0 percent of the labeled amount of cephapirin.
Packaging and storage— Preserve in Containers for Sterile Solids as described under Injections 1.
Constituted solution— At the time of use, it meets the requirements for Constituted Solutions under Injections 1.
Bacterial endotoxins 85 It contains not more than 0.17 USP Endotoxin Unit per mg of cephapirin.
Sterility 71 It meets the requirements when tested as directed for Membrane Filtration under Test for Sterility of the Product to be Examined.
Particulate matter 788: meets the requirements for small-volume injections.
Residual solvents 467: meets the requirements.
(Official January 1, 2007)
Other requirements— It responds to the Identification tests and meets the requirements for Crystallinity, pH, and Water under Cephapirin Sodium. It meets also the requirements for Uniformity of Dosage Units 905 and Labeling under Injections 1.
Assay—
Mobile phase— Prepare a filtered and degassed mixture of water, dimethylformamide, glacial acetic acid, and 11.7 N potassium hydroxide (1834:160:4:2). Make adjustments if necessary (see System Suitability under Chromatography 621). Increase the proportion of dimethylformamide to decrease the retention time of cephapirin.
Resolution solution— Prepare a solution of Cephapirin Sodium in pH 2.0 hydrochloric acid buffer (see Buffer Solutions in the section Reagents, Indicators, and Solutions) containing about 1 mg per mL. Place 10 mL of this solution in a test tube, and heat at 95 for 10 minutes, accurately timed. Promptly cool the tube in an ice water bath. Dilute 5 mL of the cooled solution with Mobile phase to obtain 50 mL of Resolution solution.
Standard preparation— Transfer about 21 mg of USP Cephapirin Sodium RS, accurately weighed, to a 100-mL volumetric flask, dilute with Mobile phase to volume, and mix. This solution contains about 0.2 mg of cephapirin per mL.
Assay preparation 1 (where it is packaged for dispensing and is represented as being in a single-dose container)— Constitute Cephapirin for Injection in a volume of water, accurately measured, corresponding to the volume of solvent specified in the labeling. Withdraw all of the withdrawable contents, using a suitable hypodermic needle and syringe, and dilute quantitatively, and stepwise if necessary, with Mobile phase to obtain a solution containing the equivalent of about 0.2 mg of cephapirin per mL.
Assay preparation 2 (where the label states the quantity of cephapirin in a given volume of constituted solution)— Constitute Cephapirin for Injection in a volume of water, accurately measured, corresponding to the volume of solvent specified in the labeling. Dilute an accurately measured volume of the constituted solution quantitatively, and stepwise if necessary, with Mobile phase to obtain a solution containing the equivalent of about 0.2 mg of cephapirin per mL. [NOTE—Use the Standard preparation and the Assay preparation within 1 hour.]
Chromatographic system (see Chromatography 621)— The liquid chromatograph is equipped with a 254-nm detector and a 4-mm × 30-cm column that contains packing L1. The flow rate is about 2 mL per minute. Chromatograph the Resolution solution, and record the peak responses as directed for Procedure: the resolution, R, between the cephapirin peak and the peak having a retention time of about 0.9 relative to that of cephapirin is not less than 0.9. Chromatograph the Standard preparation, and record the peak responses as directed for Procedure: the relative retention times are about 0.9 for cephapirin lactone and 1.0 for cephapirin; the column efficiency determined from the cephapirin peak is not less than 1200 theoretical plates; the tailing factor for the cephapirin peak is not more than 2.0; and the relative standard deviation for replicate injections is not more than 2.0%.
Procedure— Separately inject equal volumes (about 20 µL) of the Standard preparation and the appropriate Assay preparation into the chromatograph, record the chromatograms, and measure the responses for the major peaks. Calculate the quantity, in mg, of cephapirin (C17H17N3O6S2) withdrawn from the container, or in the portion of constituted solution taken by the formula:
(L/D)(CP/1000)(rU / rS),
in which L is the labeled quantity, in mg, of cephapirin in the single-dose container, or in the volume of constituted solution taken; D is the concentration, in mg per mL, of cephapirin in Assay preparation 1 or in Assay preparation 2, on the basis of the labeled quantity in the container, or in the portion of constituted solution taken, respectively, and the extent of dilution; C is the concentration, in mg per mL, of USP Cephapirin Sodium RS in the Standard preparation; P is the potency, in µg of cephapirin per mg, of USP Cephapirin Sodium RS; and rU and rS are the cephapirin peak responses obtained from the Assay preparation and the Standard preparation, respectively.
Auxiliary Information— Staff Liaison : Ian DeVeau, Ph.D., Associate Director
Expert Committee : (VET05) Veterinary Drugs 05
USP29–NF24 Page 454
Pharmacopeial Forum : Volume No. 30(2) Page 470
Phone Number : 1-301-816-8178